Latest Exam Prep

Q22. To ensure device redundancy in an HPE Campus Access network, which configurations should be applied?

Q23. You are configuring an HPE Aruba Networking Gateway Cluster with AOS-10. What is true about
802.1X functionality in combination with gateways? (Choose two.)

Q24. For enhanced port security in an HPE network, which two configurations can prevent unauthorized devices from gaining access?

Q25. You have configured BGP peering from a CX 8325 switch to a third-party router. The remote router is reachable via ping but you are not able to get the configuration to an established state.
Based on the BGP debug:

What is preventing the BGP neighbor state from becoming the established state?

Q26. Match the network technology to the customer requirement.

Q27. Refer to the exhibit and cede sample.

What is the effect when you add thestatement “neighbor 10.2.0.3 send-community both” to the ipv4 address family? (Select two.)

Q28. You are configuring VSX active gateway on CX 8360 campus aggregation switches when the switch prompt returns the following error: “No more than IB VMACs can be configured.” What should be done to address this issue?

Q29. An administrator is monitoring third-party WLAN transmitters in HPE Aruba Networking Central and some of them are classified as rogue and suspected rogue.
How are suspected rogues classified when using the default classification method for the rule
“Suspected AP On-Prem” in HPE Aruba Networking Central?

Q30. Which settings should be checked first when troubleshooting an HPE switch stack with inter- switch latency?

Q31. A customer tasked you with creating a new design for the IDFs in a large office building. A junior member of your staff took all of the technical requirements and produced a design to meet those requirements. You were asked to review the portion of the design below:
CUSTOMER REQUIREMENTS:
preference for stackable switches

Each closet should contain a single virtual switch.

dual 10Gbps fiber uplinks from each closet

capacity for 500 edge ports in each closet; no additional capacity required

lowest-cost AOS-CX switch that meets all requirements

PROPOSED DESIGN:
nine (9) AOS-CX 6200M (R8Q69A: Class4 PoE 4SFP+ switch (R8Q68A) HPE Aruba

Networking 6200M 46G 4SFP+ switch) in each closet
switches configured in a VSF (Virtual Switching Framework) stack, with auto-stacking enabled

uplinks configured on the first and last members of the stack

Does the proposed solution meet the technical requirements?

Q32. You are troubleshooting a network issue on a VSX cluster. The network was functioning properly yesterday but today the network operations center is receiving alerts. On one of the two VSX members, a ‘show interface brief’ indicated that all VSX LAGs are “down by feature”.
What could be the cause of this condition?

Q33. Refer to the exhibit.

During the update of the aggregation switches, Acc-1 clients were not able to receive multicast traffic for a few seconds. How can you improve the downtime for multicast traffic to a minimum time?

Q34. Exhibit.

A conference venue has a requirement to secure independent network users from each other in their network.
The following configurations are created on Edge-1:

Q35. Refer to the exhibit.

After implementing a distributed overlay with distributed anycast gateways, you noticed that too many ARP packets are being replicated to every access (leaf) switch.
Which command can you use to optimize the network?

Q36. Which issue may becausing the new door locks on the APs to notwork?

Q37. Which EAP methods are supported when configuring the 802.1X supplicant feature on the AOS- CX switch? (Choose two.)

Q38. Review the diagram and existing configuration of RouterA above. Which configuration changes are necessary to permit load balancing between RouterA and RouterB? (Selecttwo) Exhibit.

Q39. Which minimal configurations must becompleted for MSTP to work correctly? (Select two.)

Q40. You have a working MAC authentication solution for IoT devices using HPE Aruba Networking ClearPass and want to dynamically change the role of a device based on DHCP fingerprints.
Your security team updated the relevant ClearPass configuration, which will return the ‘IoT’ Aruba-User-Role VSA if devices match the appropriate profiling rules. The ClearPass appliance is located behind a firewall.
You have deployed the configuration below.

Which actions must be taken for the solution to work? (Choose two.)

Q41. Which statements accurately describe OSPF Graceful Restart considerations? (Choose two.)

Q42. A bgp routing table contains multiple routes to the same destination prefix. Referring to the table below, which route would be marked with a “>” symbol?

Q43. A pair of CX 8325 series switches is configured in a VSX cluster. Which function is executed on both VSX members during normal operation?

Q44. When using the cable diagnostic feature on an AOS-CX switch to lest a 1000BaseT connection, what is the accuracy of ‘distance to fault’?

Q45. Which log level on HPE switches records events that could lead to serious operational issues if not addressed?