Achieve The Utmost Performance In H31-311_V2.5 Exam Pass Guaranteed [Q27-Q44]


0
Categories : H31-311_V2.5 , Huawei
Rate this post

Achieve The Utmost Performance In H31-311_V2.5 Exam Pass Guaranteed

Achive your Success with Latest Huawei H31-311_V2.5 Exam

Huawei H31-311_V2.5: HCIA-Transmission V2.5 certification is recognized globally and is highly valued by employers. It is an essential certification for individuals who want to pursue a career in the field of transmission network technology. HCIA-Transmission V2.5 certification is a testament to the candidate’s expertise in the field and is a valuable asset when seeking employment opportunities.

Huawei H31-311_V2.5 certification exam is a comprehensive exam that consists of multiple-choice questions and simulations. H31-311_V2.5 exam requires a thorough understanding of transmission network technologies and concepts, and the ability to apply this knowledge to real-world scenarios. Passing this certification exam proves that the individual has the necessary skills and knowledge to design, deploy, and maintain transmission networks, and can be an asset to any organization looking to build or improve their transmission networks.

 

NO.27 The receiver performs a BIP-8 check on unscrambled STM-16 frames. If the BIP8 check result XOR*∶, the value of the B1 byte contained in the next STM16 ring is 10001100, which indicates STM-16 There is a () bit error block in the axis.

 
 
 
 

NO.28 After configuring PDH on a per-net element basis, the full trace cannot be searched. Which of the following is a possible cause? (Multiple choice)

 
 
 
 

NO.29 Suppose 2 VC-12 time slots need to be bound to the VCTRUNK1 of the N2EFS4 board. When there are 8 VC4 slots on the N2EFS4 board, which of the following slots meets the requirements?

 
 
 
 

NO.30 The SP3D board supports 63 E1 services

 
 

NO.31 The rate of SF64 and SL64 boards is STM54. Therefore, the two plates can be interconnected.

 
 

NO.32 Which of the following is the VLAN classification method? (Multiple choice).

 
 
 
 

NO.33 During service configuration, there are two time slot modes. Huawei uses interleaved time slot mode by default.

 
 

NO.34 The frame structure of ODU4 is four times that of ODU1

 
 

NO.35 The backplane has two 48V power cords, and each board gets two -48V power supplies from the backplane. After combining the power supply via diodes, the various voltages required for each component are obtained by means of a DC/DC power module and a linear mane swap.

 
 

NO.36 Which of the following is not a condition that triggers multiplexed segment protection (MSP)?

 
 
 
 

NO.37 The OTN signal has a fixed pad period, the same frame period as the SDH signal.

 
 

NO.38 The number of ODU2e signals multiplexed into the ODU3 signal is the same as the number of ODU2 signals multiplexed into the ODU3 signal.

 
 

NO.39 Which of the following communication protocols are used for DCN management of Huawei devices? (Multiple choice).

 
 
 
 

NO.40 Linear MSP (LMSP) has two modes: 1+1 and 1:1. Additional services can only be configured for the protection channel in 1:1 mode of the LMSP.

 
 

NO.41 Which of the following statements about overhead bytes is incorrect?

 
 
 
 

NO.42 When the sender detects that the b6-b8 of the K2 byte is 110, it means that the sender has reported an alarm ().

 
 
 
 

NO.43 Fiber loss includes bending loss, absorption loss and scattering loss.

 
 

NO.44 Which of the following clock operating modes supports the ITU-T G.781 standard? (Multiple choice).

 
 
 
 

Revolutionary Guide To Exam Huawei Dumps: https://www.vceprep.com/H31-311_V2.5-latest-vce-prep.html

         

Leave a Reply

Your email address will not be published. Required fields are marked *

Enter the text from the image below
 

DMCA Privacy Policy Contact US

© 2022 Latest Exam Prep.