Get Huawei H35-481_V2.0 Dumps Questions Study Exam Guide Dec 19, 2023 [Q24-Q43] : Latest Exam Prep : http://certify.vceprep.com

NO.24 The STR CROSFEEDTST command can be used to check for crossed feeder connections of an AAU.

True

False

NO.25 Which of the following 5G technologies can be used to ensure the QoS and security of smart grid services? (Choose One)

5G super uplink

5G E2E slicing

5G carrier aggregation

5G DNN private line

NO.26 In NSA networking, which of the following factors affect the downlink peak rate of a CPE?

Downlink transmit power of the NR base station

Uplink transmit power of the CPE

Downlink BLER of 3% or above

CPE location

NO.27 Which of the following boards do not support 5G?

UMPTc

LMPT

UMPTe

UMPTb

NO.28 Which of the following boards is added, the base station Is reset and you need to log in to the LMT again?

OUMPT

UBBP

UPEU

UEIU

NO.29 In SA networking, incorrect TAC configurations will cause UE access to fail.

True

False

NO.30 In NSA networking, X2 self-setup between a gNodeB and an eNodeB requires that the gNodeB and eNodeB be managed by the same OSS.

True

False

NO.31 What Is the maximum number of pRRUs on a CPRI link for RF combination?

12

16

8

4

NO.32 Which of the following parameters In the NR MIB message indicates the time-domain position of CORESET 0?

System frame number

Most significant four bits of PDCCH-configSIBl

SSB-subcarrier offset

Least significant four bits of PDCCH-configSIBl

NO.33 In NSA networking, X2 Interface self-setup between the 4G and 5G base stations falls. Which of the following are possible causes?

The 5G and 4G base stations belong to different PLMNs.

Cell setup fails on the LTE side.

The number of links established over the LTE X2 interface exceeds the board specifications.

The self-setup switch is not turned on.

NO.34 What does it mean when the RUN indicator of an AAU is blinking green (on for is and off for Is)?

There is power supply, but the board is faulty.

The board is working properly.

Software is being loaded to the board, or the board is not started.

There is no power supply, or the board is faulty.

NO.35 Which of the following 5G technologies can be used to ensure the QoS and security of smart grid services?

5G super uplink

5G E2E slicing

5G carrier aggregation

5G DNN private line

NO.36 Which of the following Information Is not carried In the DCI of NR?

PUSCH scheduling

PUSCH power control

PMI report

PDSCH scheduling

NO.37 If the subcarrier spacing (SCS) of a low-frequency cell Is 30 kHz and the bandwidth of each RB Is 360 kHz, theoretically, what value should the noise (dBm) over the air interface be?

-105

-116

-120

-97

NO.38 In CRAN deployment, the one-to-four cascading mode can be used for GPS clock configuration. How many BBUs at most can a GPS be connected to?

2

16

8

4

NO.39 Which of the following methods can be used to locate faults on the user-plane path?

GTPU trace

Cell DT trace

SCTP tracing result

NG interface trace

NO.40 Which of the following methods is recommended for modifying the cell bandwidths across the entire network during gNodeB data reconfiguration?

MAE-Deployment (radio network planning data file)

MAE-Deployment (batch reconfiguration)

MML

MAE-Deployment (batch reconfiguration + radio network planning data file)

NO.41 Which of the following parameters In the NR MIB message indicates the time-domain position of CORESET
0?

System frame number

Most significant four bits of PDCCH-configSIBl

SSB-subcarrier offset

Least significant four bits of PDCCH-configSIBl

NO.42 Which of the following statements about a self-contained slot is Incorrect?

Faster downlink hybrid automatic repeat request (HARQ) feedback and UL data scheduling to reduce the RTT.

Increased GP overhead due to frequent uplink-downlink switching.

High requirements on latency of terminal hardware processing.

Prolonged sounding reference signal (SRS) transmission period to track fast channel changes and Improve MIMO performance.

NO.43 Which of the following synchronization rasters can be used by a UE during a cell search?

17.28MHz

1200kHz

1.44MHz

100kHz