This page was exported from Latest Exam Prep [ http://certify.vceprep.com ] Export date:Sat Dec 14 12:39:05 2024 / +0000 GMT ___________________________________________________ Title: VALID NACE-CIP1-001 Exam Dumps For Certification Exam Preparation [Q34-Q50] --------------------------------------------------- VALID NACE-CIP1-001 Exam Dumps For Certification Exam Preparation NACE-CIP1-001 Dumps PDF 2023 Strategy Your Preparation Efficiently Q34. The initial steel condition is important to the NACE Inspector because:  If the steel is pitted more coating will be required  Less abrasive is need if the mill Scale s gone  It affects the final appearance after blasting  The Inspector may have to reject the Steel Q35. Osmotic blistering is most likely to occur as a result of  inadequate anchor pattern/surface profile.  overcoating a surface contaminated with chemical salts.  airless spray application  applying tine coating too thin. Q36. Owners hire NACE Inspectors’ with the expectation that:  The inspection cost will be offset by an improvement in service life  The Inspector will improve job flow and schedule  The Inspector will make a meaningful technical contribution to the job  a) and c) Q37. The least effective method of surface cleaning is most likely  water blasting.  dry grit blasting.  hand tool cleaning.  power tool cleaning. Q38. What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?  70% of the specified maximum thickness  80% of the specified minimum thickness  90% of the specified maximum thickness  100% of the specified maximum thickness Q39. You are the NACE Inspector on a job where the Owner’s specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.Your FIRST preferred course of action is to:  Skip the checks as you are. confident the blast pressure is OK  Skip the checks and just record the same readings as you have been getting  Keep doing the checks regardless  Keep doing the checks and consult the Owner’s representative for direction Q40. Safety Data Sheets must be carefully reviewed by:  The Application personnel  The Inspection personnel  The Owner’s personnel  All personnel involved in the job Q41. ISO ST 3 is described as:  Thorough hand tool cleaning  Very Thorough power tool cleaning  Very Thorough hand or power tool cleaning  Thorough blast cleaning Q42. When holiday testing is required the Inspector is always required to enforce NACE SP 0188:  True  False Q43. You are an inspector on a project where SSPC SP 3 is specified.What sort of tools should you expect the Contractor to use to achieve the standard?  Abrasive blast nozzles  Power tools  Hand tools  Airless spray equipment Q44. The Inspector should record the serial numbers of inspection instruments:  Only if the specification requires it  Each time the instrument is used  Only if the instrument is suspected of not working properly  Only when verifying accuracy of the instrument Q45. The most important factor resulting in improved job site safety is:  Personal Protective Equipment  Engineering Controls  Safety Enforcement  Situational Awareness Q46. Galvanic corrosion occurs on which of the following substrates:  Concrete  Fiberglass Reinforced Plastic  Metal  Wood Q47. Surface profile describes:  The level of surface cleanliness required after abrasive blasting  The level of surface roughness required after abrasive blasting  The initial condition of the surface prior to abrasive blasting  The general condition of the surface required after abrasive blasting Q48. Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:  Rust Grades A-D  Surface Conditions E-G  Rust Grades 1-4  Surface Condition H Q49. If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:  Level 1  Level 2  Level 3  Level 4 Q50. Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:Select All That Apply  Using a damaged gauge  Dragging a gauge through wet coating  Placing the gauge along the longitudinal axis  Loading … Latest Verified & Correct NACE-CIP1-001 Questions: https://www.vceprep.com/NACE-CIP1-001-latest-vce-prep.html --------------------------------------------------- Images: https://certify.vceprep.com/wp-content/plugins/watu/loading.gif https://certify.vceprep.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2023-01-09 16:42:09 Post date GMT: 2023-01-09 16:42:09 Post modified date: 2023-01-09 16:42:09 Post modified date GMT: 2023-01-09 16:42:09